3D printers · Voron
Owners who built a Voron 2.4 keep it for clean, detailed prints (ASA included) at speeds well past their older machines, and accept doing their own repairs when a part fails.
Print quality is the most consistent good thing in these accounts, though only a few owners raised it. One gets better ASA prints than from a Bambu C1 at about twice the speed, and another describes excellent results years after building it.
Owners are divided on speed, and too few raised it to settle it. One says theirs prints well but slowly, and thinks an Ender 3 gives cleaner results. Another runs far higher acceleration and speed than the Ender 3 that printed its parts.
The Voron 2.4 is a 3D printer from Voron Design that you build yourself. Voron Design is an open-source project that publishes the plans, not a company that sells finished printers. It suits hobbyists who want to source the parts, put the printer together and tune it themselves.
| Build volume | 250 mm, 300 mm or 350 mm cube (custom sizes also possible) |
|---|---|
| Printer type | |
| Max speed | |
| Nozzle temperature | |
| Bed temperature | |
| Enclosure | |
| Auto bed levelling | |
| Warranty |
From the maker's spec page, checked October 8, 2026. A blank row means the maker does not state it.
You choose how big to build it. The 250 mm version prints objects up to about 25 cm on each side, and the 350 mm version goes up to about 35 cm, which fits large parts but needs more desk space. Speed and temperatures depend on the parts you pick. Since you build it yourself, Voron Design gives no warranty.
Pick up to three. You get a page with just those, side by side, on the subjects owners raised.
For one owner who built theirs years ago, daily use is now simple: switch it on, give it about half an hour to heat up, then print. The good results haven't worn off. Another owner is still pleased by how fast their build runs compared with the Ender 3 they used to print its parts.
Living with it also means changing it over time. Owners mention fitting a new door and running a Dragon UHF hotend. Not everyone thinks it out-prints simpler machines: one owner prefers how clean their Ender 3's output looks, even though it is much slower.
One long-term owner calls their 2.4 low maintenance and very reliable, years after building it. On the other side, an owner whose EBB36 v1.2 toolhead board stopped reading thermistors correctly was several days into rebuilding the toolhead. They compared that with a C1 that has run a long time with only basic upkeep. When something breaks, these owners fix it themselves.
The long-term evidence here is thin. Only a few owners talked about reliability, and they don't agree, so this page can't say how a typical 2.4 holds up over years.
From 0 owner accounts that said how long they have had it. Own one? Add how long yours has lasted.
Nothing has a clear majority against it yet. Counted from the owners who raised each subject, not from everyone. A subject is judged once at least 4 owners raise it.
11 more subjects came up from fewer than 4 owners each, which is not enough for a fair reading. To see how it stacks up, compare it with another machine.
The same owner, asked again at each point. Fills in as owners answer.
Two questions: how long you have had it, and anything you would like to say about it. Then we ask again as it ages. This helps our mission.
More in 3d printers: Creality Hi, Bambu Lab X1C, Prusa Mk3.
Among the 0 owner accounts here that gave a duration, 0 described a failure.
Before you buy one used, ask the seller: how old it is, whether it was ever repaired and by whom, and whether any of the parts above have been replaced. Ask to see it run. A receipt tells you the warranty start date; most makers honour the term only for the first owner.
Public discussions we read and summarised in our own words. Nothing here was submitted to Still Kicks.
Counted from public accounts by people who said they own it, and summarised by Still Kicks in its own words. Not a manufacturer claim, a lab test or an estimate.
No account needed to look. Sign in with Google only if you want to track something you own.